Fun, Learning, Friendship and Mutual Respect START  HERE


Unregistered
Go Back   HeliFreak > Multi Rotor Support > Flight Controllers (NAZA, Wookong, A2, etc...) > DJI Multirotor Forum(A2/WKM)


DJI Multirotor Forum(A2/WKM) DJI Multirotor Forum(A2/WKM)


Reply
 
LinkBack Thread Tools Display Modes
Old 12-30-2015, 03:34 PM   #1 (permalink)
Registered Users
 

Join Date: Feb 2014
Default WKM & Zenmuse H3-3D Settings

Hi
I am in need of some help and guidance. I have a X650 Quad, that I have just setup the WKM flight controller, I also have a Zenmuse H3-3D Gimble for my GoPro.
I have completed the basis setup, but I am having some trouble setting up the return to home switch, and the tilt for the Gimble. My radio is a Futuna 14SG, with upgraded firmware to allow multi rotors to be selected as a mode.
The issue is this. The tilt by default is connected to the right slider. When I move the position of the camera, the return to home is activated as well. I have tried to separate these functions, but have failed.
If there is anyone who can offer a solution, or would be willing to post their settings I would be very great full.
Thank yo in advance.

Keith
cripboy is offline        Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 12-30-2015, 06:36 PM   #2 (permalink)
HF MR Support
 
Posts: 4,534
 

Join Date: Nov 2012
Default

Have you looked at the servo monitor to see what's moving when you move the the RS?
__________________
3 years cancer free! Woot!! ~ Cancer can kiss my grits! Ainokea!
If you never crash, you're not having enough fun!

Pilot, Team Lavaquad
Big Island Guy is offline        Reply With Quote Quick reply to this message
Old 12-31-2015, 04:45 PM   #3 (permalink)
Registered Users
Thread Starter Thread Starter
 

Join Date: Feb 2014
Default

Hi
Yes, that was one of the first checks. Only 1 channel us moving.

Keith
cripboy is offline        Reply With Quote Quick reply to this message
Old 12-31-2015, 09:31 PM   #4 (permalink)
HF MR Support
 
Posts: 4,534
 

Join Date: Nov 2012
Default

This sounds like it might be a PPM framing problem then. Does RTH happen the moment you start moving the slider or is it happening more towards the end of its travel? If so, you might try backing off the the slider's travel limits a bit and see if that helps. Also, make sure your Futaba controller is in a channel mode compatible with your RX's.
__________________
3 years cancer free! Woot!! ~ Cancer can kiss my grits! Ainokea!
If you never crash, you're not having enough fun!

Pilot, Team Lavaquad
Big Island Guy is offline        Reply With Quote Quick reply to this message
Reply




Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the HeliFreak forums, you must first register.
Please enter your desired user name, your REAL and WORKING email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself. Use a real email address or you will not be granted access to the site. Thank you.
Email Address:
Location
Where do you live? ie: Country, State, City or General Geographic Location please.
Name and Lastname
Enter name and last name here. (This information is not shown to the general public. Optional)
Helicopter #1
Enter Helicopter #1 type and equipment.
Helicopter #2
Enter Helicopter #2 type and equipment.
Helicopter #3
Enter Helicopter #3 type and equipment.
Helicopter #4
Enter Helicopter #4 type and equipment.

Log-in


Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On




Copyright © Website Acquisitions Inc. All rights reserved.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.

SEO by vBSEO 3.6.1